Extron MTP RL 15HD A MTP Twisted Pair Transmitter With Power for VGA and Audio

Description

Extron MTP RL 15HD A MTP Twisted Pair Transmitter for VGA and Audio With Power.
Like New Condition - May have very minor scratches on housing.
TESTED - WORKING
Specifications: MTP 15HD A Series
Video
Gain
Unity
Number/signal type
1 set of proprietary analog signals
Connectors
MTP R 15HD RSA D
1 female RJ-45 on a pigtail
All other models
1 female RJ-45
Video input and loop through — transmitters
Number/signal type
MTP T 15HD A
1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video
1 buffered RGBHV, RGBS, RGsB, RsGsBs local monitor loop through (includes ID bits)
MTP T 15HD A AAP, MTP T 15HD A D, MTP T 15HD A WM
1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video
Connectors
MTP T 15HD A
2 female 15-pin HD
All other transmitters
1 female 15-pin HD
Nominal level
1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video
Minimum/maximum levels
0.3 V to 1.45 Vp-p
Impedance
75 ohms
Horizontal frequency
15 kHz to 130 kHz
Vertical frequency
30 Hz to 150 Hz
Return loss
<-30 dB @ 5 MHz
DC offset (max. allowable)
250 mV
Video output — receivers (MTP RL 15HD A, MTP RL 15HD A SEQ, MTP R 15HD RSA D)
Number/signal type
MTP R 15HD RSA D
1 analog VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs, HD component video, component video, S-video, or composite video
All other receivers
1 set of proprietary analog signals
1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video
Connectors
MTP R 15HD RSA D
1 female 15-pin HD
All other receivers
1 female RJ-45
1 female 15-pin HD
Nominal level
1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video
Minimum/maximum levels
0.3 V to 1.45 Vp-p
Impedance
75 ohms
Return loss
<-30 dB @ 5 MHz
DC offset
MTP R 15HD RSA D
<±20 mV with input at 0 offset
All other receivers
<±35 mV with input at 0 offset
Skew compensation
62 ns
Maximum resolution
Up to 1920x1200 or 2048x1080 or 1080p at 300'
Up to 1024x768 at 600'
NOTE
See the user guide for the maximum distances recommended for specific resolutions.
Sync
Input type (transmitters)
RGBHV, RGBS, RGsB, RsGsBs
Output type (receivers)
RGBHV, RGBS, RGsB, RsGsBs
Standards
NTSC 3.58, NTSC 4.43, PAL, SECAM
Input level (transmitter)
3.5 V to 5.5 Vp-p, unterminated
Output level (receivers)
4.0 V to 5.0 Vp-p, unterminated
Input impedance (transmitter)
573 ohms ±5%
Output impedance (receivers)
110 ohms
Max. input voltage (transmitter)
5.5 V p-p
Polarity
Transmitter
Positive or negative (follows input polarity)
Receivers
Positive or negative (switch-selectable)
Audio — all models
Number/signal type
1 set of proprietary analog signals
Connectors
1 female RJ-45
Gain
Unbalanced output: 0 dB; balanced output: +6 dB
Frequency response
20 Hz to 20 kHz, ±1 dB
THD + Noise
0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level
S/N
>70 dB at maximum output (unweighted)
Stereo channel separation
>60 dB @ 1 kHz
CMRR
>43 dB @ 20 Hz to 20 kHz
Audio input — transmitters
Number/signal type
1 stereo, unbalanced
Connectors
(1) 3.5 mm mini stereo jack
Impedance
>10k ohms, unbalanced
Nominal level
+4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level
+18 dBu, (unbalanced) at 1%THD+N
NOTE
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio output — MTP T 15HD A AAP, MTP T 15HD A D, MTP T 15HD A WM local stereo output
Number/signal type
1 stereo, balanced/unbalanced
Connectors
(1) 3.5 mm direct insertion captive screw connector, 5 pole
Impedance
50 ohms unbalanced, 100 ohms balanced
Gain error
±1 dB channel to channel
Maximum level (Hi-Z)
>+23 dBu, balanced or unbalanced at 1% THD+N
Maximum level (600 ohm)
>+17 dBm, balanced or unbalanced at 1% THD+N
Audio output — receivers
Number/signal type
MTP R 15HD RSA D
1 mono, balanced/unbalanced
All other receivers
2 mono, balanced/unbalanced
Connectors
MTP R 15HD RSA D
(1) 3.5 mm captive screw connector, 5 pole (uses 3 poles)
All other receivers
(1) 3.5 mm captive screw connector, 5 pole
Impedance
50 ohms unbalanced, 100 ohms balanced
Gain error
±1 dB channel to channel
Nominal level
+4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level
MTP R 15HD RSA D
14 dBm, unbalanced at 1% THD+N
All other receivers
+18 dBu, unbalanced at 1% THD+N
Control/remote — external device (pass-through, unidirectional or bidirectional) — MTP R 15HD RSA D only
Serial control port input/output
1 set of proprietary signals on a female RJ-45 jack
Serial control port output/input
RS-232 via 3 poles of a 3.5 mm captive screw connector, 5 pole
Baud rates
Up to 38400 bps at up to 1000' (304.8 m) (Higher data rates and distances are possible. Performance varies based on baud rate and cable length.)
Protocol
Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none
NOTE
Protocol is mirrored between the transmitter and the receiver.
Serial control pin configuration
Captive screw connector: 1 = Tx, 2 = Rx, 3 = GND
General
Recommended cable type
CAT 5/5e/6 (shielded or unshielded)
Power supply
External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts
Power input requirements
12 VDC, 0.5 A
Temperature/humidity
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling
Convection, no vents
Mounting
Rack mount
MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ
Yes, with optional rack shelf
Furniture or wall mount
MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ
Yes, with optional under-desk mounting kit
MTP T 15HD A AAP
Yes, with optional AAP mounting faceplates that have double space high AAP opening
MTP T 15HD A D, MTP R 15HD RSA D
Yes, in a decorator-style opening with a standard electrical wall box or standard 1-gang US size mud ring
MTP T 15HD A WM
Yes, in a 1-gang opening
Pole mount
MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ
Yes, with optional pole mounting kit
Enclosure type
Metal
Enclosure dimensions
MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ
1.7" H x 4.3" W x 3.0" D (1U high, quarter rack wide)
4.3 cm H x 10.9 cm W x 7.6 cm D
(Depth excludes connectors.)
Faceplates
MTP T 15HD A AAP
1.4" H x 3.5" W x 0.1" D (3.6 cm H x 8.9 cm W x 0.3 cm D)
(double space high AAP plate)
MTP T 15HD A D, MTP R 15HD RSA D
2.6" H* x 1.3" W x 0.1" D (6.6 cm H* x 3.3 cm W x 0.3 cm D)
(Fits the opening in a 1 gang, 4.4" H x 2.7" W decorator-style wallplate. Depth excludes connectors.)
*Overall height is 4.1" (10.4 cm) including mounting tabs.
MTP T 15HD A WM
4.5" H x 2.8" W x 0.1" D (11.4 cm H x 7.1 cm W x 0.3 cm D) (1 gang)
Device
MTP R 15HD RSA D
2.75" H x 1.65" W x 1.3" D
(7.0 cm H x 4.2 cm W x 3.3 cm D)
(Depth excludes connectors.)
Other AAP, D, and WM models
2.7" H x 1.4" W x 1.4" D (6.9 cm H x 3.6 cm W x 3.6 cm D)
(Depth excludes connectors.)
Product weight
0.4 lbs (0.2 kg)
Regulatory compliance
CE, C-tick, c-UL, UL, FCC Class A, ICES, VCCI
Product warranty
3 years parts and labor
Everlast power supply warranty
7 years parts and labor
NOTE
All nominal levels are at ±10%.
NOTE
Specifications are subject to change without notice